Showing posts with label Rifle Articles. Show all posts
Showing posts with label Rifle Articles. Show all posts

Tuesday, June 11, 2013

.308 Winchester, Gotta LOVE It

As the title says, you gotta love the .308 Winchester, especially in the Savage stainless steel, synthetic stocked Weather Warrior persuasion with Accu-Trigger.

I went to the club today with three different factory loads partially to check my deer hunting zero with a previously chosen load and partly to find out if I could use this rifle on a baited black bear hunt out to 75 yards or so without having to change the scope setting. The answer to both questions was POSITIVE.

See the photo of my hastily put together target below. Starting at the left of the target, the first orange sticker was Federal's 150 grain power Shok factory load at 75 yards. The middle target is the load for which the gun has been sighted in for (Winchester's 150 grain Power Point) and the one on the right is Remington's round nose soft point Core Lokt 180 grain load.

The gun is certainly good to go as is out to 200 yards (previously tested last summer with same scope setting) with the Winchester 150 grain Power Points. The surprise came at 75 yards with the 180 grain round nose Core Lokt which would make a DANDY black bear over bait load. Actually most baited bear sites are closer to the tree stand or ground blind than 75 yards. The farthest black bear hunt bait site I have been at was with Carey Outfitters in Maine about 3 years ago and that was exactly 50 yards.

Take a look:

RANGE CONDITIONS 6/11/2013: Raining moderately hard and steady and light gusting winds

FROM left to right, the caliber and bullet weight, velocity, bullet ballistic coefficient,  100 yards, 200 yards and Midrange trajectory (maximum yardage where the point of impact does NOT rise more than or hit lower than 3 inches from line of sight. From the charts, you can see that there isn't a nickel's worth of difference out to 269 yards (which is farther than MOST of us shoot) and has NO bearing at all on a "Baited black bear hunt" which is the topic here.

.308 Win. (180 Sp 2610).483+2.8"+1.2"3"@125 259


.30-06 (180 Sp at 2700).483+2.7"+1.5"3"@125269

I have NO particular problem with the 30:06 per se, except ONE. My own personal experience has been that having owned (3) different 30:06 rifles over the years and also (3) different .308 rifles over the years, the .308 Win IN MY OWN PERSONAL EXPERIENCE.......Your's may vary......is more accurate with various bullet weights than the 30:06.

NO black bear that ever lived (IF possible) would send you an email, indicating that they could tell the difference between a well placed bullet with a .308 Win and a 30:06. From 75 yards in, back to your tree stand or ground blind, I would pick the most accurate of either rifle and for my experience it has always been the .308 Win.

In the target below the left side (2) shots at 75 yards of Federal 150 grain Power Shok's went into 1/2 inch center to center. The middle target with the Winchester 150 grain PP went into 1/4 inch center to center and the Remington 180 grain Core Lokt round nose loads (far right target) went into 13/16 center to center.




Having owned (3) previous rifles in BOTH 30:06 and .308, my experience indicates it is RARE to find a rifle that will handle any three different factory loads this well. IF I wanted to switch to the Federal Power Shok load for hunting, a simple 3 clicks right and perhaps 6 clicks down would put me right where I need to be. I have to admit that the accu-trigger set up on the Savage no doubt adds to this rifle's accuracy.

Dan

Friday, March 29, 2013

RUGER's NEW Guide Gun

I am impressed by Ruger's new guide rifle and thought I would post the specs here. First of all I think they did this right and have pretty much covered all the basis for a harsh climate, rugged easy to maneuver rifle.

The rifle weighs 8.12 lbs in all calibers, has a 20 inch stainless hammer forged barrel, the new LC6 trigger, adjustable pull length by inserting or removing a shim (from 12.75 to 14.25 inches), an adjustable rear sight with a bead front, integral bases for scope mounting, a muzzle brake system, 3 position safety, and a  green mountain laminated stock.  OH, I almost forgot......a great recoil pad. Someone at Ruger obviously did their homework and included many of the features that would make a perfect rifles in Alaska or any wet climate for either a hunter or a guide.

Caliber line up is as follows:


  • .300 RCM
  • .300 Win Mag
  • 30:06 
  • .338 RCM
  • .338 Win Mag
  • .375 Ruger


If you can't get it done with one of these, better stay home.

Dan

Here is a link to the Ruger Guide Rifle:

http://www.ruger.com/products/guideGun/features.html


Tuesday, March 26, 2013

Magnums (vs.) Ordinary Cartridges?

Came across a chart from an outdoor magazine from 2001 concerning the real world trajectory and ballistics of ordinary cartridges such as the 30:06, .270 Win and  the ( .35 Whelen which was more popular in 2001 than it is today). I am going to post some of the numbers here for you to look at. I am a firm believer that through out most of the N/E anyway, most deer are still shot under 100 yards and most of the remainder are shot at under 200 yards. I use the phrase "Most Deer" as I have known a few people who are consistently capable of making shots between 200 and 400 yards. I also realize that under ideal conditions off a bench rest with wind flags set out, a top end ballistic plex fully multi-coated  scope and your rifle locked into a Caldwell Lead sled and with a spotter calling your shots that more of us would fit into that 200-400 yard scenario.

Unfortunately under field conditions most of us cannot take advantage of 200-400 yard shots quickly. All that being said, how much real world difference is there between the standard calibers and the magnums for the average hunter at 300 and 400 yards? Chart below is with a 200 yard zero.

These figures are based on what was available in 2001, however there is not as much difference as one might imagine even in 2013.

                                                                      300 yard drop              400 yard drop
.270 Win, 130 grain bullet @3100fps                   6.3                               18.5
.270 Wby. Magnum 130 grn @3300fps               5.5                               16.0
.280 Rem 150 grain @3000fps                            6.6                                19.3
7mm Mag 150 grain @3200                                5.8                                16.7
30:06 180 grain @2700                                       8.5                                24.4
.300 Win mag 180 grain @3200fps                      6.5                                19.1
.338-06 225 grain @2600fps                               9.3                                26.7
.338 Win Mag 225 grain @2900fps                     7.2                                21.0
.35 Whelen 250 grain @2500fps                         10.0                               29.4
.358 Norma mag 250 grain @2700fps                 8.6                                 24.8

Interesting line up of bullet weights and muzzle velocities and yet the difference in bullet drop at 300 yards between the fastest and slowest calibers is only 4.5 inches. At 400 yards it is 10.7 inches.

If you compare the .270 Win with 130 grain loads to the vaunted 7mm Mag with a 150 grain bullet, the difference at 300 yards is only 1/2 inch and at 400 yards is 1.8 inches We can certainly argue the 7mm Mag starts its 150 grain bullet out of the gate 100fps second faster than the .270 does with a 130 grain bullet. I doubt there is a whitetail walking anywhere that could tell the difference at either range with a proper hit in the vitals. If we are talking about elk or moose at those distances, then I would agree that the 7mm Mag is the better choice, or better yet one of the .300 mags.

In closing my old  FFA agricultural teacher in high school always used to say, "Variety is the spice of life."
We all become attached to different rifles for various reasons, some of which are based on ballistics, or because your Dad killed 27 deer with your favorite rifle and never lost a one of them etc.

FREEDOM to choose is part of what makes America great. Our 2nd amendment rights are under attack as NEVER before so make sure your NRA dues are paid and I would encourage you if you have not done so to make your voice heard with your state and federal Representatives today.

Dan

Friday, March 22, 2013

Maximum Point Blank Range MPBR for Whitetails

I thought it might be interesting to pick three calibers one would consider for long range deer hunting as would occur in the western states, or on the prairies of Saskatchewan or even over looking a corn field or hay field in my own upstate NY from a tree stand.

MPBR stands for maximum Point Blank Range and is the distance at which a rifle's bullet will keep its trajectory within a PLUS or MINUS 3 inches.

My past post was about winning a western deer hunting sweepstakes where the airfare, guide, accommodations etc. are part of the sweepstakes, however you must bring your own rifle. Today I am going to look at how a .308 Win, .270 Win and a .300 WSM stack up against each other out to 300 yards.

http://www.chuckhawks.com/rifle_trajectory_table.htm

Information below is taken from an article and tables (SEE LINK ABOVE) by Chuck Hawks. Please refer to his article for additional information and tables on other cartridges. Chuck is one of my favorite writers.

Here is a ballistic printout of the three cartridges showing the caliber, bullet weight, muzzle velocity, bullet BC, trajectory at 100 and 200 yards and mid range trajectory MRT keeping the bullet within a PLUS or MINUS 3 inches. Finally MPBR - is the maximum distance at which the bullet will fall below the 3 inch low trajectory:

Caliber/bullet/MV/ Bullet BC/100 yds/200 yds/MRT/MPBR

.270 Win. (130 Sp at 3140).416+2.5"+2.4"3"@150305
.270 Win. (140 AB at 2950).496+2.6"+2.1"3"@140293
.270 Win. (150 Sp at 2900).481+2.6"+2.0"3"@138287

The above table show the .270 keep the 130 grain within that 3 inch variation out to 305 yards, the 140 grainer to 293 yards and the 150 grain to 287 yards.In other words there is only 18 yards separating the three bullet weights so all would be acceptable out to 300 yards on whitetails. I would simply choose whatever load shot the most accurately out of my rifle.

Let's look at the .308 Win: Here there is only 16 yards separating the 3 inch differential for all three bullet weights, however one can see the .270 is the better long range whitetail gun.

.308 Win. (150 BT at 2800).435+2.7"+1.7"3"@135275
.308 Win. (165 Sp at 2700).410+2.7"+1.3"3"@130264
.308 Win. (180 Sp at 2610).483+2.8"+1.2"3"@125259


Lastly take a look at the .300 WSM (Winchester Short Mag). Here essentially you are gaining a few yards and have the advantage of a larger caliber, heavier bullet. The 180 grain bullet out of the .300 WSM basically duplicates the approximate trajectory of the 140 grain bullet out of a .270 Win in a .30 caliber rifle with a 40 grain heavier bullet. IF I owned all three rifles and won the trip or managed to go on another trip like that, it is an easy decision to take the .300WSM.

I did go on a trip to Saskatchewan a few years ago with the Ruger .330 Win Mag and 180 grain bullets and never looked back. I did manage to see two different real bruiser bucks that I used a range finder to determine were on the far side of 450 yards. I did not take the shot. I passed up a couple lesser bucks inside of 150 yards which any of the three rifles above would have been more than adequate. Whitetails are whitetails and are not difficult to kill. That being said, Saskatchewan whitetails are BIGGER, sometimes a lot bigger and I would prefer the .300 WSM in that situation. The other item to consider is your bullet is going to get blown around more at 350-400 yards than it will under 200 yards. A heavier .30 caliber bullet traveling just as fast as your .270 bullet is an advantage.

Dan


.300 WSM (150 BT at 3300).435+2.4"+2.6"3"@150321
.300 WSM (180 Sp at 2970).483+2.6"+2.2"3"@150294

Thursday, March 21, 2013

The .270 Win As a Long Range Whitetail Rifle

I entered a sweepstakes on line the other day for a whitetail hunt out west and got to thinking what rifle would I take if I won?  It was a free hunt for two including airfare, guide, accommodations etc. It was a BYO rifle however and not a complete package deal. The smart thing if I had the money would be to probably buy a new rifle in one of the .300 Win Mags or better yet the .300WSM.

I let my Ruger .300 Win mag go several years ago on a trade for something else. I also let the 30:06 go a while back. My two best in house candidates would be the .308 Savage Weather Warrior and the older Ruger Model 77 Mark II in .270 Win.

Since the game would be whitetails, I would likely take the .270 Win with whatever factory load shot the best. I would probably opt for one of the premium 130 grain bullets available for a flatter trajectory.

The .270 has better long range ballistics than the .308 does and since the game is whitetails only, one of the premium 130 grain loads that shoot real well would be just the ticket. One could argue and probably convince me that I should never have let my Ruger .300 Win Mag go and simply use that. I do regret letting that rifle set up slip through my hands, however what is done is done. If I ever had the money to get another one, I would probably buy one of the .300WSM rifles.

Dan

http://www.gunnersden.com/index.htm.270winchester-ballistics-hunting.html


In the chart below with a 130 grain bullet and a 200 yard zero, the bullet only drops 5.7 inches at 300 yards and -16.7 at 400 yards. The .270 would make a good 300-350 yard rifle on whitetails.



270 Win. Ballistics:
Rifle Barrel Length: 24 Inches.
Ammuntion: Hornady, 270 Win., 130 Grain SST Bullet, Superformance.
Bullet Diameter: .277 Inch.
Bullet Weight: 130 Grains.
Bullet Ballistic Coeffecient: .460.
Note: FPS. = Feet Per Second, FT. LBS. = Foot Pounds & IN. = Inches.
Range
Muzzle
100 yds.
200 yds.
300 yds.
400 yds.
500 yds.
Yards
Bullet Velocity:
3,200
2,984
2,778
2,582
2,393
2,213
FPS.
Bullet Energy:
2,955
2,570
2,228
1,924
1,653
1414
FT. LBS.
Bullet Trajectory:
- 1.5"
+ 1.2"
0"
- 5.7"
- 16.7"
- 33.7"
IN.

Another Link to .270 Win performance:

http://www.ballisticstudies.com/Knowledgebase/.270+Winchester.html

EXCERPT:

"I am going to post only the factory ammunition load data here as I do not hand load any longer:

Factory ammunition

Today, there is a huge range of factory ammunition for hunters to chose from and it is common for factories to offer two to three distinct lines of ammunition, standard, semi premium and premium. For the hunter, shopping for .270 ammunition can end up a confusing and frustrating affair. More often than not, hunters, regardless of their financial means, will opt for a low priced load and buy several packets in order to gain practice.

Winchester Olin, PMC, Remington, Hornady and Federal all offer basic entry level 130 and 150 grain soft point bullets. In earlier days, these designs were the feature loadings. Muzzle velocities for the 130 grain loads now average 3030fps from 24” barrels. Both Federal and Winchester offer the hottest loads producing between 3050 and 3060fps, right on advertised specifications. PMC is now the slowest at 2900fps but makes for a good light recoiling medium game, moderate range load, duplicating the 6.5x55 Swedish Mauser with hand loads.

Generally speaking, the basic factory 130 grain soft point loads produce hydrostatic shock on medium game down to an impact velocity of 2600fps. Remington, Federal and Olin loads stay above the 2600fps figure out to between 150 and 175 yards. Between the impact velocities of 2600fps and 2400fps, hydrostatic shock is absent but wide wounding leads to fast killing in a matter of a few seconds. The above factory loads break the 2400fps at between 250 and 275 yards. At impact velocities below 2400fps or beyond 275 yards, wounds become narrow and killing delayed. At these ranges, rear lung shots should be avoided in favor of the forwards shoulder point of aim.

Winchester Olin standard loads currently feature the 130 grain Power Point at a true 3060fps in 24” barreled sporters, the 130 grain Silver Tip also at 3060fps and the 150 grain Power Point advertised at 2850fps for a realistic 2780fps. The ball powder used by Winchester in their 130 grain loads loses little velocity in shorter 22” barrels to the order of 20fps per inch of barrel lost while the 150 grain load is true to the rule of thumb losing 35fps per inch.

The 130 grain Power Point and Silvertip are ideally suited to lighter deer species but each performs differently. The Silver Tip’s original aluminum ballistic tip gives explosive expansion for cross body lung shots while an attempt to arrest mushrooming occurs at the cannelure which in turn tends to cause a delayed but gradual total disintegration of the projectile . The 130 grain Power Point offers slightly more controlled expansion and although the Silver Tip will sometimes exit lighter medium game on cross body shots, the Power Point’s longer wound channel is more able to create a broader exit wound for blood trailing.

The 150 grain Power Point load gives around 2710fps in the average 22” sporter, duplicating factory .308 Win 150 grain loadings. The low velocity of this loading, initially designed to minimize meat damage, also helps control expansion and prevents bullet blow up at close ranges. The Power Point produces fast killing on medium game at close ranges, creating free bleeding exit wounds on cross body shots. Nevertheless, this load suffers in open country at ranges beyond 100 yards due to the low velocity resulting in narrow wounds.

Olin’s semi premium Supreme load features the130 grain Nosler Ballistic Tip for a true 3050fps. Marketed under the brand name Ballistic Silvertip CT (Winchester Nosler Combined Technologies), the Nosler is dressed with a Grey colored polymer tip to symbolize the traditional Silvertip bullet. The Ballistic Silvertip is coated in black colored Lubalox which decreases bore friction allowing loads easily reach advertised velocities within industry pressure specifications.

Ballistically superior to the original Silvertip, the BST is designed purely for long range open country work on medium game. Terminal performance is very similar to the original Silvertip and identical to the 130 grain Sierra GameKing where velocity is equal. At close ranges, energy transfer occurs incredibly fast, creating large internal wounds which peter out quickly. On animals over 40 kg ( 80 lb ) cross body shots result in either a small exit wound or none as the remainder of the projectile comes to rest under the skin. The BST will either disintegrate or shed its core when striking pelvic bone at close range, a clue as to why Nosler developed the Partition Bullet many years ago. At longer ranges, the BST comes into its own, simply due to higher BC’s than traditional .270 offerings which translates into higher downrange velocity for wider wounding. The BST remains above 2400fps out to 325 yards.

During the mid 1990's Winchester released the 140 grain Failsafe at 2920fps. With its Lubalox coating and four expanding blender blade like petals, the Failsafe was marketed quite aptly as the Black Talon along with an eagle claw emblem. The front of the Failsafe is similar to the Barnes X while the rear features a lead insert similar to the Partition. The Failsafe is an extremely stout bullet, out penetrating all .270 hunting bullets on the market. The Failsafe produces the smallest frontal area of all .270 projectiles and likewise can produce equally small wound channels. On lighter animals, the Failsafe gives slow kills, even at close range, when shots strike behind the shoulder into the rear lungs. If shoulder bones are struck, an extremely violent wound channel is created which momentarily bells out the offside skin. If the gut is breached during the projectile’s travel, gut fiber follows the path of the bullet and becomes trapped in large clumps under the skin where it was temporarily belled ( similar to the 300 magnums. ) This bullet is best suited to animals weighing in excess of 150 kg (330 lbs ) and an optimum choice, though at its absolute limit, if using the .270 for neck shooting heavy game.

A recent addition to the Winchester supreme line is the Nosler 140 grain Accubond (Lubalox coated) producing a mild 2950fps in 24” barrels and 2880fps in 22” barrels. As an all-round medium game bullet for the .270, the Accubond is one of the best on the market. While higher muzzle velocities would be useful, the Accubond performs well out to 300 yards on a variety of game and produces broad wounding for fast kills.

One of the more commonly used brands of ammunition because of its economy, is PMC ammunition. Standard loads in the Bronze line include the 130 grain soft point at an advertised 2950fps and 150 grain at 2750fps. The 130 grain load is regularly used by budget minded hunters and at realistic muzzle velocities of 2900fps, is a lower recoiling, modest performing load giving best performance inside 250 yards.

PMC Silver brand loads include the Sierra 130 grain GameKing at 3050fps and the 150 grain GameKing at 2850fps. The 130 grain GK works well at the true muzzle velocities of 2900fps, producing fast, uniform kills with ordinary cross body and slightly quartering shots on medium game inside 250 yards. The 150 grain bullet is definitely different. On lean animals, kills can be delayed due to a lack of energy transfer. The 150 grain GK is best used on game weighing above 80kg (180lb) as a safe minimum. At 2750-2800fps, this load is again best used out to moderate, rather than longer ranges. That said, penetration of the GK launched at 2750-2800fps is much better than the typical jacket core separation that occurs when this bullet is hand loaded to 2950fps and driven into vitals from raking angles.

The PMC Gold line features the 130 grain Barnes TSX at 2910fps and 150 grain TSX at 2700fps. Although these are both good projectiles, the velocities of PMC ammunition in sporting rifles are far too low for optimum performance.

Current light weight loadings from the Hornady Custom line include the 130 grain SST and 130 grain Interlock bullets at an advertised 3060fps. Both loads produce over 3000fps in 24” barrels and 2920fps in 22” barrels. Neither of these loads are as good as one might come to expect from Hornady.

The Interlock soft point is prone to total disintegration at close ranges when striking bone while the SST is prone to suffer early jacket core separation under the same conditions. In some cases, penetration of the SST may be as little as 6”. Nevertheless, both projectiles produce wide wounds and fast killing when matched to light framed game. No doubt both bullets have been used to take most North American game however for best performance, limiting as it may seem, both loads are best suited to game weighing less than 60kg. The SST produces fast killing out to 325 yards, the Interlock soft point producing best performance inside 275 yards.

The 130 grain SST is also offered as a Superformance loading at 3200fps. Along with this, Hornady now manufacture the 130 grain GMX bullet at 3190fps for around 3120fps in 22” barreled sporters. This homogenous copper bullet, like the Barnes TSX, does its best work at either close range/ high impact velocities or on tougher animals. The GMX is ideally suited to game weighing above 90kg (200lb) and up to 320kg (700lb).

Medium weights from Hornady include the 140 grain Interlock BTSP at an advertised velocity of 2940fps for just over 2900fps and 2830fps respectively along with the 140 grain SST Superformance load at 3090fps giving around 3020fps in 22” barrels. Of these, the SST is the more spectacular killer on medium game and even though it is only 10 grains heavier than the often shallow penetrating 130 grain SST, the 140 grain version is a better bullet. Neither of the 140 grain bullets are totally reliable for close range raking shots on Whitetail sized deer however wounds created by the SST are usually severe enough to slow animals down and allow for fast follow up shots. The 140 grain SST SF load is extremely violent and fast killing out to 275 yards, retaining its ability to produce broad wounding out to 400 yards.

The heavy weight of the Hornady line is the 150 grain Interlock at 2840fps for realistic velocities of 2770fps. This soft bullet opens up quickly on impact, even at low velocities. Penetration is usually excellent on cross body and quartering shots but poor with tail on shots. Unfortunately, approximately one bullet in one hundred will suffer bullet blow up on the shoulder bones of game weighing as light as 60kg (130lb). The lower velocities of this load do help minimize occurrences of bullet blow up but also dictate that the 150 grain Interlock is best suited to closer ranges if high shock and broad wounding is to be maximized.

Remington’s traditional .270 130 grain loadings are the Bronze point and Core-Lokt at an advertised at 3060fps. The Bronze point performs similarly to Winchester’s Silvertip, an explosive design for open country hunting while the Core-Lokt utilizes controlled expansion. From current velocities of around 3030fps, the Core-Lokt does its best work inside 250 yards while the Bronze point is superior out at the 300 yard mark due to its ability to create wider wounds. As much as the Core-Lokt projectile is a good performer on game, there is an definite change from fast killing inside 250 yards to very slow killing at 275 yards with rear lung shots. For fast kills at longer ranges, the Core-Lokt must be driven through shoulder bones. The Bronze point has a more aerodynamic shape in comparison to the flat tip design of the Core-Lokt but it does not have a greatly superior BC. Performance is instead, enhanced through the use of the more explosive bullet design.

Remington’s heavyweight standard loading consists of the 150 grain round nose Core-Lokt at an advertised 2850fps for true velocities of 2800fps. This is a well designed projectile and while it would have been nice to have a pointed 150 grain Core-Lokt at 2950fps, the factory 150 grain loading is sufficient for bush/woods hunting large medium game.

Remington have, in the past, made several attempts to produce high grade ammunition. For many years, performance was retarded by low velocities. The 135 grain and 140 grain Remington Extended Range loadings are prime examples, neither achieved over 2800fps in 22” barreled sporters. Next came the 130 grain Nosler Ballistic tip but again, fairly mild at around 2850fps. With competition being centered around high velocity loadings, Remington finally made more effective changes.

The latest .270 offering under the brand name Remington Accutip, is similar, if not identical to the Hornady 130 grain SST (it may well be). The Accutip is colored bronze in line with Remington's original Bronze Point ammunition. The 130 grain Accutip loading produces 3060fps in 24” barreled sporters and 2990fps in 22” barrels. Performance is identical to the SST.

Remington now offer 3 core bonded loadings in their premier range. These include the 130 grain Swift Scirocco at 3060fps, the 140 grain Core-Lokt Ultra at 2925fps and finally the 140 Swift A-Frame, also at 2925fps. The 130 grain Scirocco is a fast expanding, fast killing bullet suitable for all around work on medium game. Like the InterBond, penetration is excellent on medium game with all but tail on shots. The 140 grain Ultra is similar to the Scirocco in terminal performance but lacks the high BC of the sleek Swift bullet. The A-Frame, which has a very similar shape to the Core-Lokt, is the stoutest of the three, offering deeper penetration and optimum performance on Elk sized game.

Federal’s traditional standard .270 loads include the 130 grain Hi-Shok at 3060fps and 150 grain Hi-Shok round nosed at 2850fps. These loads are also branded as Vital-Shok and more recently- American Eagle. Construction of the Hi-Shok is near identical to the Remington Core-Lokt however the Federal projectiles are somewhat more brittle and prone to lose vast amounts of weight when striking bone. Like the Core-Lokt, the 130 grain Hi-Shok has a low BC and loses a great amount of velocity over a moderate range, resulting in very slow kills beyond 250 yards with rear long shots. This load is usually extremely accurate in a wide variety of rifles- providing the rifle itself is an accurate platform. It therefore goes without saying that at 300 yards, using an accurate rifle, the Hi-Shok load can produce fast kills with extra care to shot placement.

The Federal Premium branded ammunition features both standard and enhanced velocity (HE) loadings for bolt action rifles. Loads include the 130 grain Sierra GameKing, the 130 grain Nosler Ballistic Tip and 130 grain Partition, the 130 grain Barnes TSX, the 130 grain Fusion (core bonded), the 140 grain Trophy Bonded Bear Claw, 140 grain Accubond, 145 grain Fusion, 150 grain GameKing, 150 grain Partition and finally, the 150 grain Fusion.

Unfortunately, Federal’s attempts to try and cover all bases has a tendency to cause more confusion rather than offering solutions. Furthermore, most gun store owners simply cannot afford to carry such a vast range of stock. Several of these loads duplicate the performance of others within the line and are ultimately, counter productive.

The 130 grain Sierra GameKing and Ballistic Tip bullets at 3060fps produce identical results on game. Explosive wounding and adequate penetration for cross body and quartering shots on lighter medium game are the hallmarks of these bullets. It is somewhat unfair that the GameKing is listed as a premium projectile because as a reloading component, the GK is a basic budget cup and core style projectile. Realistically, Federal could or should replace the Hi-Shok bullet with this very fast killing and accurate offering.

The 130 grain Partition was, as mentioned, a favorite of Jack O’Connor’s. Although O’Connor used this bullet on all game, the 130 grain bullet is better suited to lighter animals and on game weighing less than 80kg, the 130 grain Partition really shines. The Partition is always at its best when correctly matched to the job at hand. The 130 grain projectile has a low SD and simply cannot be expected to give the same deep penetration that the 150 grain Partition is capable of.

The 130 grain TSX at 3060fps is best suited to use on larger animals, weighing above 80kg (180lb), up to the size of Elk with ordinary chest shots. On lighter animals, as velocity falls below 2600fps (225 yards), the TSX does not meet enough resistance to impart shock within the first half inch of penetration. Kills on light game can slow regardless of the usually good internal wounding. This can however be avoided by ensuring shots are aimed to strike major shoulder bones and the forwards section of the lungs.

The 130 grain Fusion bullet at 3060fps is a fast killing bullet on lighter medium game inside 250 yards. Penetration is on par with the Partition although slighty better where heavy bone is encountered. Apart from this, the Fusion offers nothing that cannot be done with the Barnes 130 grain TSX.

The 140 grain TBBC is offered at a velocity of 3100fps. Why Federal felt the need to offer both the 130 grain Barnes and the similar 140 grain TBBC is anyone’s guess. Performance of the TBBC duplicates that of the TSX.

The 140 grain Accubond at 2950 is as already mentioned, a very good load. The Accubond is somewhat faster expanding and faster killing than the 130 grain Fusion at longer ranges or the 150 grain Fusion at all ranges.

The 150 grain Sierra GameKing advertised at 3000fps, gives around 2950fps in 24” barreled sporters and around 2880fps in 22” barrels. The 150 grain GameKing is an odd projectile; too stout for fast kills on light game with rear lung shots but too soft to be useful on larger medium game. This load is perhaps best suited to game weighing right around the 80kg (180lb) mark at extended ranges of 200 to 350 yards- a very narrow range of performance.

The 150 grain Partition is an excellent projectile, one of the very best. Ironically, Federal load this projectile to 2850fps for a realistic 2800fps rather than the much more useful velocity of 2950fps (from 24” barrels)."


The only change I would make might to my current rifle would  be a new higher end scope with a ballistic plex set up of some sort on it.

A couple of options to consider from SWFA:



Nikon 2.5-10x42 Monarch 3 RiflescopeNikon 2.5-10x42 Monarch 3 Riflescope
Stock # - NIK6763
  • Matte
  • Mil-Dot
  • 1"
$399.95


Bushnell 3-9x40 Elite Rifle ScopeBushnell 3-9x40 Elite Rifle Scope
Stock # - BUSE3940B
  • Matte
  • DOA™ 600
  • 1"
  • RainGuard® HD
  • Ultra-Wide Band Coating
  • Argon Purging Process


$349.00

Wednesday, March 6, 2013

Big Bores For Black bear

I thought it might be interesting to take a look at the 12 gauge shotgun with slugs (vs.) the 45-70 (vs.) a .50 cal muzzle loader for black bear over bait. Up front, I have to say they will all do the job very nicely but its fun to look at the numbers.

Take a look at a few 12 gauge slug offerings:

Lightfield Hybred Sabot Slugs

546 grain 3inch MEXP at 1730fps
546 grain 2 and 3/4 inch sabot slug at 1450fps

Remington 12 gauge 3 inch 1 ounce copper solid sabot slug at 1550fps / 2331 ft lbs

Federal power Shok saboted slug 12 gauge 2 and 3/4 ounce 1500fps
Federal 3 inch 300 grain copper sabot slug 2000fps / 2664 ft lbs

A Few 45-70 loads that make the grade:

Hornady 325 Grain FTX Lever Evolution Ammo (Many bears have been taken already with this load)

Buffalo Bore has several loads available for the 45-70 in Marlin Lever Action Rifles:

I have shot the following two loads: (Either will do for black bear and the 405 grain load has a great reputation on black bear over bait)

405 grain JFN Expander / designed to penetrate up to 2 feet in flesh and bone and expand to 1 inch diameter / 2000fps and 3597 ft lbs
350 grain JFN Penetrator designed to penetrate up to 4 feet and expands to .60 caliber / 2150 fps and 3591 ft lbs

.50 caliber muzzle loader / the loads available for this set up are too numerous to mention here:

In spite of that, here are a few:

ALL loads would work with either 100-110 grains of Pyrodex RS or 2 /50 grain/ .50 cal Pyrodex pellets. You would need to put in range time to determine the most consistently accurate load out of your In-line .50 cal rifle.

Barnes all copper 250 grain, 285 grain or 300 grain TMZ spitfire saboted load

TC 250 and 300 grain saboted Shock Wave loads / preferably BONDED bullets

295 grain Power Belt bullets

TC Maxi Ball full bore sized loads 350 grain

Dan


Monday, February 18, 2013

NEW .17 Rimfire magnum at 3000fps

Here is a look at the NEW .17 Rimfire magnum from Winchester at a stated muzzle velocity of 3000fps.

http://search.yahoo.com/search;_ylt=A2KLtSoJfyJREVYAhTObvZx4?p=NEW+.17+rimfire+at+3000fps+velocity%3F&toggle=1&cop=mss&ei=UTF-8&fr=yfp-t-701-1

Here is another link:

http://www.youtube.com/watch?v=1v74JZ2ikDI


I will add no comments except to say if you are going to purchase a new rifle this year for shooting prairie dogs, crows, woodchucks within range limits etc. you might want to look at this NEW .17 rimfire magnum. If you were thinking of buying a .17HMR, I would definitely take a look at this one.

Dan

Here is a nice article and test by "GUNBLAST":

http://www.gunblast.com/Ruger_77-17.htm



Sunday, February 17, 2013

Range Test .338 Federal After Ruger Repair

I finally got a chance to go to the range yesterday to check out the Ruger Hawkeye .338 Federal after getting it back from the factory. As mentioned in a recent post, they replaced the trigger with a NEW LC6 trigger set a 3.5 lbs, new sear, polished the feed ramp, rails etc. and repaired the feeding problems.

I ran a couple of different factory loads through the action without firing the gun before going to the range. The load that was giving me the most trouble getting hung up and not chambering etc. was the Federal 210 grain Nosler Partition load.

In any event, I took the rifle to the range yesterday and the wind was so bad that when I originally set up at 100 yards, the wind knocked my target stand and target over twice. I then moved the target to 50 yards and fired only six shots total. Three were with the 210 grain Nosler Partitions and the other 3 were with another Federal practice load in 200 grain weight. (The 210 grain Partitions are on the left target and the other load on the right is also from Federal in the 200 grain uni-cor soft point Power Shok.




The Nosler Partition is good for anything that you would want to hunt with a .338 Federal and would be my choice for larger black bear, elk, moose etc. The 200 grain Power Shock Uni-Cor is listed on the box as a medium game load with a picture of a whitetail on the front.


I was not so much looking for group size as I was functioning of the rifle and checking any improvement in the feeding process. I was not disappointed in either arena as without trying to shoot tight groups, and putting three rounds of each load through the gun fairly rapidly, the results were great. There were no hangups and the hinged floor plate style magazine seemed tighter and the rounds snapped into place much better than they had before the repair.

In any event, I am a happy camper and hopefully might get out in the next year or two for another baited bear hunt up in Maine.

Dan

Here is a photo of the 50 yards target.







Here is an excerpt from my 11/28/2012 Post concerning the repair:


Contact:

Sturm Ruger & Co. Inc
411 Sunapee St.
Newport, NH 03773
603-865-2442
(Have your model and serial number available when you call as they will assign an RMA number to your order and they will email you a shipping label as they pick up the charge both ways for UPS.)

I did a couple of range sessions after purchasing the rifle mostly with the Federal 200 grain fusion load. I didn't have any recurring problems till I started running the 210 grain Nosler Partitions through it. In any event based on reading the gun forums and realizing that there were some real issues with the Hawkeye series rifles in .338 Federal, I decided to ship the gun to Ruger to take a look at it.

I was very impressed with the whole process. They had the gun approximately two weeks. They sent me by email a shipping label and an RMA number to identify the gun while it was in their possession. they paid the shipping both there and back so it ended up costing me zero.

Notes included in the box with the rifle which arrived yesterday indicated they had replaced the existing trigger with a NEW LC6 trigger, NEW sear, NEW spring, NEW stock screws, repaired feed ramp, rails, bolt and trigger pull is at 3.5-4 LBS.

They then test fired the rifle at their range with NO mention of the distance involved. The photo copy of the range target indicated that Federal 185 grain factory load was used and it shows a nice tight 3 shot clover leaf group.

There was also a note which solves the mystery on at least the front stock screw. The note indicates "THE FRONT MOUNTING SCREW SHOULD BE TORQUED TO 95 INCH POUNDS".

This for me solves the dilemma of endless opinions on line concerning the tightness of the front screw. As mentioned previously my Wheeler Fat Wrench only goes to a MAX of 65 inch pounds and I was getting 3/4 inch groups with the Factory fusion load at 75 yards at last testing. I have never tried the Federal 185 grain load, however may make the switch based on their attached target.

Thursday, February 7, 2013

.450 Marlin (vs.) the 45-70

As mentioned in my previous posts several times, I own a Marlin Model 1895 45-70 with a Wild West Happy Trigger installed and a Bushnell 1.5X4.5X32 with firefly riding on top. I like this gun. I really like this gun. It shoots well with a variety of factory ammo (I don't hand load anymore) and it shoots better than most bolt action rifles when loaded with Hornady's 325 grain FTX Lever Evolution ammo.

I thought about buying a .450 Marlin when I bought the 45-70, so why didn't I.

Several reasons:

The 45-70 has been around a long time (while the .450 Marlin began its life in 2000) and ammo for it can be found at a variety of ammunition outlets (important if the .450 Marlin loses its popularity and ammo is hard to find).
I know I can go on a remote bear hunt and in an emergency I can find a box of Remington 45-70 ammo in a remote place.
With 45-70 loads from Garret, Buffalo Bore, CorBon and others, one could hunt about any animal that walks the earth. (The Garret loads especially in my opinion are unbeatable when going after the brown or grizzly bears, buffalo and other large species)
Corbon also loads a 460 grain CorBon Hunter HC load at 1650fps and 2780 ft. lbs only for the 45-70
With all due respect for the .450 Marlin as it IS A super caliber, the 45-70 can do everything that the .450 Marlin can and MORE.

Dan

Let's look at factory ammo comparing the two calibers:

.450 Marlin:

Hornady offers two different bullets in this caliber:

The same 325 grain FTX Lever Evolution load as the 45-70 only slightly FASTER out of the chute
2225 fps velocity and 3572 ft. lbs of energy at the muzzle
A 350 grain Hornady Interlock FP
2100fps velocity
405 grain soft point
1975fps
430 grainer
1900fps

Buffalo Bore offers three current loads for the .450 Marlin, and (5) loads for the 45-70

https://www.buffalobore.com/index.php?l=product_list&c=43

https://www.buffalobore.com/index.php?l=search_list&s[search]=45-70+loads&s[title]=Y&s[short_desc]=Y&s[full_desc]=Y&s[sku]=Y&s[match]=all&s[cid]=0

Garret Cartridges offer (5) loads for the 45-70 and NONE for the .450 Marlin

http://www.garrettcartridges.com/4570.html

EXCERPT:

Garrett Cartridges Of Texas - Products


Garrett's 45-70 Government Ammo

420-gr SuperHardCast Hammerhead at 1650-fps

Please see Ballistic Info for Recommended Firearms
$80 / 20 CTGS
Add to Cart Ballistic Info


Garrett's 45-70 plus p Hammerhead Ammo

420-gr SuperHardCast Hammerhead at 1850-fps
Please see Ballistic Info for Recommended Firearms
$80 / 20 CTGS
Add to Cart Ballistic Info


Garrett's 45-70 plus p Hammerhead Ammo

540-gr SuperHardCast Hammerhead at 1550-fps
Please see Ballistic Info for Recommended Firearms
$80 / 20 CTGS
Add to Cart Ballistic Info


Garrett's 45-70 plus p SuperJack Ammo

350-gr Woodleigh Weld-Core JSP at 2000-fps
Please see Ballistic Info for Recommended Firearms
$90 / 20 CTGS
Add to Cart Ballistic Info


Garrett's 45-70 plus p Exiter Ammo

500-gr Hornady Copper Clad Steel Jacketed Flatnose Solid at 1530-fps

Please see Ballistic Info for Recommended Firearms
$150 / 20 CTGS
Add to Cart Ballistic Info

LINK below for penetration tests:

http://www.garrettcartridges.com/penetration.html

EXCERPT:

PENETRATION: THE 45-70 & 458 MAGNUMS

The following article is based on bullet penetration test results as measured in water-saturated penetration materials (wet newspapers). Water is the primary substance of life, and constitutes about 90% of the content of all mammals.  I have observed that some "testers" have chosen wood boards or dry newspapers for penetration testing material, and this is a very poor choice, which in no way simulates the characteristics of a bullet impact with animal flesh.  Wood tends to channel the bullet path, and is less demonstrative of the terminal instabilities inherent to non-expanding bullets when impacting game animals, and is thus an inferior material for the testing of bullet penetration characteristics. Water-saturated penetration materials such as newspapers or ballistic gelatin are far superior with regards to their ability to demonstrate the terminal instabilities that typically occur when non-expanding bullets impact live animal flesh. - Randy Garrett
There are few things in the world of ballistics less well understood than the issues relating to comparative penetration. It is commonly believed that the faster one drives a solid bullet, the deeper the penetration. We see this all the time in the various attempts, via new calibers, to achieve higher velocity for improved performance on heavy game. The current rage among big bore shooters seems to be the 458 Lott, since it achieves a good 200-300 fps higher velocity than the 458 Winchester Magnum. It is claimed that the new 458 Lott is an improvement over the 458 Winchester Magnum since its higher velocity supposedly results in more lethal impact-effect and deeper penetration. This, it is claimed, is just the ticket for busting the heaviest game. Of course, the new 458 Lott also achieves greater kinetic energy as a result of its higher velocity, and this is also a convincing characteristic for those brave souls in pursuit of the heaviest game.

Despite all the impressive "science" deployed to reinforce the assertion that higher speed projectiles are more capable of inflicting the deep penetration and impact-effect required to reliably anchor heavy game, one finds that these assertions simply do not withstand common sense, repeatable penetration testing. In fact, if one conducts these tests, one finds that there is nothing that can be observed which supports the assertion that the faster one drives non-expanding solids the deeper they penetrate.
Very interestingly, if one takes the Hornady 500-grain .458 diameter solid bullet and compares the penetration that results from impact speeds varying from about 1500-fps to 2500-fps, one finds that the higher impact speeds produce the least penetration. When driven to about 1500-fps (as the 45-70 will do) one finds that such solids produce nearly 6-feet of penetration in wet newspapers. When the same bullet is driven to about 2100-fps (as is characteristic of the 458 Winchester Magnum) one finds that the penetration is reduced to about 4 to 4 and 1/2 feet. When one tests the same bullet at 2300-2400 fps (as is characteristic of the 458 Lott) one finds that the penetration comes up nearly 20% short of that produced by the 458 Winchester. And when one tests the same bullet at the blistering speeds characteristic of the mighty 460 Weatherby Magnum, one finds that the penetration achieved is the most shallow produced by the various 458s.

What is apparent from testing is that penetration stops increasing at impact speeds above about 1250-1300 fps. When the impact speeds significantly surpass about 1600-fps, there is a very definite and measurable decrease in penetration depth. This raises some interesting issues regarding the relationship between kinetic energy generation and impact-effect. Although higher velocity projectiles always generate more kinetic energy they clearly do not produce deeper penetration, and when the velocities reach the levels common to today's magnums, the increases in velocity result in significantly reduced penetration. Simply stated, the faster they strike the faster they stop.
Fortunately for all of us who shoot the 45-70, it can be considered to be the deepest penetrating of the various 458 calibers. This is not due to any particular inherent superiority, but due to the 45-70's "inability" to achieve the velocity with heavy bullets that leads to decreases in penetration. The reasons why high impact speeds reduce penetration are not well understood. However, anyone who takes the time to run comparative penetration tests will find that those of us who pack a good 45-70 with heavy bullets need not take a back seat to any other 458 caliber, especially when the game is heavy and the penetration requirements are great.
- Randy Garrett





Monday, February 4, 2013

.338 Federal (vs.) .338 Marlin Express

I thought about buying a .338 Marlin Express rifle at the time I purchased my Ruger Hawkeye .338 Federal rifle. Why didn't I?

Most rifle purchases are personal and often times have nothing to do with logic per se as much as emotion, looks and the old adage, "I just wanted one".

Here is a little of the logical side of the argument and process I went through in my mind at the time.

 Ballistic comparisons on both cartridges:

.338 Marlin Express 200 grain LeverEvolution ammo:

                                    Muzzle     100 yards    200 yards   300 yards   400 yards

Velocity fps                 2565         2365           2173          1991           1819
Energy Ft.-lbs              2921         2483           2097          1760           1469
Wind drift 10MPH       0                0.9              3.6             8.4             15.4
Trajectory inches        -1.5            3                 1.3             -7.8             -25.5





.338 Federal with 210 grain Nosler Partition factory load

Velocity fps               2630          2412           2204            2007           1821
Energy Ft-lbs             3225          2712           2265            1878           1546
Wind Drift 10MPH     0                0.9               3.7             -8.7           16.3
Trajectory inches      -1.5              3                  1.6             -7.1          -24.4  

There is a slight advantage in velocity, energy in foot pounds out to 400 yards for the ,338 Federal. Do I personally consider that a big deal? Not really. Most animals are not impressed with ft-lbs of energy anyway, especially big bears. There is also the matter of the Marlin sporting a 24 inch barrel (vs.) the Ruger Hawkeye's handier 22 inch barrel. I also feel the Nosler 210 grain partition is perhaps better suited to the big bears if one had the opportunity to hunt them. Either caliber is capable of taking whitetails, black bear, moose, wild boar, elk, and similar game out to 300 yards and maybe 400 if you practice enough to become proficient with your rifle.






Based on the M77 Hawkeye Standard model, this rifle features a weather-resistant stainless steel barrel and receiver in Hawkeye Matte Stainless finish, and a rugged black synthetic stock.


My feeling at the time were that I already owned two Marlin  rifles in 45-70 and .35 Rem which were both MOA rifles with the LeverEvolution ammo from Hornady.

I just liked the look and the feel of the Ruger Hawkeye and felt the .338 Federal with a wider choice of ammunition was the better deal for me. The .338 Federal has factory loads available from 180 grains to the 210 grain Nosler Partition. My particular rifle shoots the 200 grain Federal Fusion load the best and it is capable of doing about anything one would want to do with the .338 Federal cartridge. I also was influenced by the possible longevity of the .338 Federal cartridge (vs) the longevity of the .338 Marlin Express. I dearly love my .350 Rem Mag as an example, however it isn't easy finding factory ammo for it anymore. I think however I have found someone locally that I can rust to hand load round for that rifle.

I support all of those who purchased either one. That is part of what made America great....Freedom of choice. I pray every day our current crop of politicians in Washington are not allowed to take that away from us.
           
Dan

King James Bible (Cambridge Ed.) 2 Chronicles 7:14
If my people, which are called by my name, shall humble themselves, and pray, and seek my face, and turn from their wicked ways; then will I hear from heaven, and will forgive their sin, and will heal their land.


The 2nd Amendment was ratified on December 17, 1791 along with the other nine amendments that make up the Bill of Rights. While it is a very short amendment, its exact meaning in terms of what types of weapons are protected is still in contention today.

Text of the 2nd Amendment

A well regulated Militia, being necessary to the security of a free State, the right of the people to keep and bear Arms, shall not be infringed.

Thursday, January 3, 2013

Bear Rifles RE-visited

Now that deer season is over in NYS, my mind is turning back to bear rifles. As mentioned in a recent post, I had sent my .338 Federal to Ruger for some work and recently received it back. I am currently out of 200 grain Fusion loads, however I do have some 210 grain Nosler Partition loads on hand. A couple of boxes of the Federal fusion load are on order and when they arrive I plan on making an afternoon trip to the local range to put the .338 Federal back through its paces.

I suspect the .338 Federal with the fusion load would make a dandy load for black bear, whitetails and about anything one would want to kill with the .338 Federal. IF I were booking a grizzly/brown bear hunt, and using this rifle, I would opt for the 210 grain Nosler Partition load.

With bullets weighing in at 185 grains to 210 grains, the .338 Fed is reputed to give between 1820 to 1920 ft lbs of energy at 300 yards. It does that with less than 9 inches of drop at 300 yards when zeroed at 200 yards. Nothing to sneeze at. I will not begin to try and make a case for this caliber being the equal of the ,338 Win mag......IT ISN'T. On the other hand most of us do not need a .338 Win mag for hunting whitetails, black bear, moose etc.

http://www.youtube.com/watch?v=6qdumOj9W6Q



I am currently considering possibly selling my Ruger .350 Rem mag. I might also consider trading it for  a new 30:06 or even a NEW .35 Whelen. Factory ammo for the .350 mag is scarce and  expensive, however I am looking into finding someone locally that will reload for me and change my mind. Part of the problem is that brass is also limited and expensive and it doesn't appear at this point in time that Remington Arms is going to step up to the plate and start making new brass for this caliber. It is a shame as I  dearly love the ergonomics and handling capabilities of this rifle and fortunately it is very accurate.

I bought this rifle primarily to use with the 225 grain Nosler partitions if I ever got an opportunity and finances to go on a brown bear hunt. Because of the ammo shortage situation, I might resign myself to use the .338 Federal with 210 grain Nosler partitions and let it go at that.

I also have the Marlin mdl 1895 45-70 and for black bear, whitetails etc. I am happy to use the 325 grain Hornady Leverevolution factory loads. They are extremely accurate out to 200 yards which is as far as I have tested them at the range. If I were hunting brown bear with this gun there is an amazing variety of custom loads for this rifle including Garret Hammer Heads that will take anything that walks and also big critter loads from CorBon, Buffalo Bore and others.

In closing I sometimes regret not having the ability to know the future. If I had that power, I would have purchased the Remington bolt action BDL in .35 Whelan instead of the Ruger 77 .350 Rem Mag a few years ago. The only reason being the shortage of not only factory ammo but also brass for the .350 mag. At the same time, .35 Whelan factory ammo or custom loads can still be had through several outlets for a reasonable price. I don't believe the .35 Whelan has any significant performance margin over the .350 Mag per se, it is just easier to obtain ammunition.

Here is a older link to an EXCELLENT review of the Remington Mdl 600 (vs.) the Ruger 77 in .350 mag caliber. The article is by one of my favorite writers, Chuck Hawks:

http://www.chuckhawks.com/compared_350Mag_rifles.htm

EXCERPT:

Conclusion
Both of these rifles incorporate some good features. For rifles of their power they are handy and fast handling, with good portability. The .350 Remington Magnum cartridge is an excellent one. Both rifles are very accurate, more so than they really need to be. At the range there is little to choose between the two, although the Remington's superior trigger (after adjustment) makes it easier to shoot accurately, and its effective recoil pad makes it more comfortable.
In the field it is a different story. Although the Remington 673 Guide Rifle is an adequate hunting rifle, the Ruger M77R Mk. II Standard rifle is superior in most areas. Perhaps the most significant difference is that the Ruger's few deficiencies are easy to correct (principally a recoil pad and a new trigger assembly), while the Remington's problems are fundamental design deficiencies.




(MY INPUT)

I handled rifles in both calibers at the local Gander Mountain store a few years ago and ended up finding a Ruger for sale on line brand new in the box. If I had not found the Ruger on line, I would have choosen the BDL .35 Whelan OVER the Model 600 carbine in .350 mag. Hind sight being 20/20 it seems history would have now proved me smarter in the long run to have went with the .35 Whelan from an ammunition availability stand point. I keep HOPING that Remington Arms will see the light and start producing factory ammo in both 200 grain and 250 grain persuasion again along with selling NEW brass for the .350 mag at a reasonable price.  When they decided to promote the Model 600 in .350 mag again a few years ago, my understanding is they all sold out rather quickly. They OWE it to those of us who snatched up a .350 mag to at least occasionally run a quantity of 200 grain and 250 grain corelokts and make enough brass to keep those rifles going.They already have the tooling for it and I think they would sell the brass and ammo as fast as they could make it.

Dan



Wednesday, December 5, 2012

Hunt In The Rain...THEN CLEAN YOUR GUN

Do you hunt in the rain and snow? Dumb question right? Most of us do especially in NYS. Today is Dec 5, 2012 and although it rained some this morning, it turned to wet sloppy snow later this afternoon. The other day I hunted for 4 hours in pretty much steady hard rain. Probably should have called it a day early, however I tend to hunt when I can hunt and just accept whatever the weather man deals out.

Had (2) encounters this week with the same big buck and still did not bring him home with me. Both episodes involved being seen by the buck before I saw him and both involved running shots. I MIGHT have been able to make either one of them, however I passed them both up. WHY? The first one involved not knowing what was over the ridge from where the buck was running and the one today involved not wanting to take a risk on gut shooting a really nice buck and having him end up as coyote food if I didn't recover him. He was running through some high grass, golden rod, scrub trees etc. and although I was able to track him with the scope, that split decision part of my brain could not bring myself to pull the trigger. Hey it happens.

Now I am at home writing this BLOG Post and second guessing myself. I probably could have made the shot, however I made a decision at the time and I will live with it. I HOPE to see him again before the season is up and maybe next time will be a standing shot.

I had my Savage Weather Warrior .308 Stainless bolt action with a black synthetic stock both times. The gun is called a "Weather Warrior" for a reason and that is why I use it when it is nasty out. On the other hand, that doesn't mean you can "Ride it hard and put it away wet".

It is extremely weather resistant, however it is not impervious to the elements. So how do I clean it?

I bring it inside, remove the bolt, remove the electrical tape over the end of the muzzle and let it stand in the corner muzzle down till it is dry. Then I run a cleaning patch with a little CLENZOIL on it through the bore. I follow up with a dry patch. I wipe the outside of all metal parts with a cloth again with clenzoil on it. I wipe down the bolt and I run a ML cleaning brush with a clenzoil damp cleaning patch in far enough to wipe down the feed ramp and bolt rails etc. I clean the scope and dry it off and clean the lenses and then I finish up by putting a drop or two of oil on the sling swivels and wipe them off.

Wait a minute...............NOT quite done yet. Since the Savage has a free floating barrel, I take a cleaning patch or cut a strip from an old T-shirt, put a little clenzoil on it and run it up and down the barrel channel where it is free floated to get any moisture and dirt etc. out of that area. I also of course remove the magazine (clip) and wipe that down with a dry patch with a little oil on it.

Then I put it away.

A clean gun is a happy gun.

Dan







Dan

Wednesday, November 28, 2012

.338 Federal Ruger Hawkeye Factory Repair

I recently sent my Ruger Hawkeye .338 Federal bolt action rifle back to the Ruger folks in New Hampshire. I had not shot the rifle much in the last two years and did start again to have some trouble with cycling the bolt and feeding cartridges into the chamber. This occurred mainly with the Federal 210 grain Nosler partition factory loads. I had taken the rifle to a local gunsmith when I first purchased it to lighten the trigger and check to see if there were any feeding problems with the gun. IF I lead any readers astray with my initiall post some time ago about no apparent feeding problems, I APOLOGIZE. As mentioned I did not do a lot of shooting with the rifle and probably should have before announcing mine did not have a problem. IF you own a Hawkeye .338 Federal and you are having bolt cycling and feeding problems, Ruger will absolutely take care of it and it will cost you nothing including shipping both ways.

Contact:

Sturm Ruger & Co. Inc
411 Sunapee St.
Newport, NH 03773
603-865-2442
(Have your model and serial number available when you call as they will assign an RMA number to your order and they will email you a shipping label as they pick up the charge both ways for UPS.)

I did a couple of range sessions after purchasing the rifle  mostly with the Federal 200 grain fusion load. I didn't have any recurring problems till I started running the 210 grain Nosler Partitions through it. In any event based on reading the gun forums and realizing that there were some real issues with the Hawkeye series rifles in .338 Federal, I decided to ship the gun to Ruger to take a look at it.

I was very impressed with the whole process. They had the gun approximately two weeks. They sent me by email a shipping label and an RMA number to identify the gun while it was in their possession. they paid the shipping both there and back so it ended up costing me zero.

Notes included in the box with the rifle which arrived yesterday indicated they had replaced the existing trigger with a NEW LC6 trigger, NEW sear, NEW spring, NEW stock screws, repaired feed ramp, rails, bolt and trigger pull is at 3.5-4 LBS.

They then test fired the rifle at their range with NO mention of the distance involved. The photo copy of the range target indicated that Federal 185 grain factory load was used and it shows a nice tight 3 shot clover leaf group.

There was also a note which solves the mystery on at least the front stock screw. The note indicates "THE FRONT MOUNTING SCREW SHOULD BE TORQUED TO 95 INCH POUNDS".

This for me solves the dilemma of endless opinions on line concerning the tightness of the front screw. As mentioned previously my Wheeler Fat Wrench only goes to a MAX of 65 inch pounds and I was getting 3/4 inch groups with the Factory fusion load at 75 yards at last testing. I have never tried the Federal 185 grain load, however may make the switch based on their attached target.

I will likely NOT mess with the factory setting and for the most part have NO need to remove the barreled action from the stock anyway. I will leave that alone.

Observations:

It appears the feed ramp has been polished, along with the rails, and a note of the bolt being repaired without any specifics.

I have NOT been to the range and likely will not get there till after deer season in NYS. I did cycle 8 rounds of the Nosler 210 grain Partitions through the action without incident and noticed that the rounds sit in the magazine better and snap into place smartly which they did not do previously.

The trigger is more than okay and has no over travel and is very crisp. I am happy with the work they have done and the professionalism and courteous folks I talked to at the repair center.

I have remounted the Bushnell 3X9X40 elite 3200 scope and am anxious to get back to the range and do some accuracy testing off the bench. (CLICK on the target photo to enlarge and read the note concerning 95 inch pounds of torque on the front mounting screw)

Dan